Konfigurasi Router EIGRP Di Cisco Packet Tracer

 Konfigurasi Router EIGRP Di Cisco Packet Tracer

Langkah awal untuk konfigurasi EIGRP yaitu dengan membuat jaringan sederhana dulu,
 contoh seperti gambar di bawah :

 Langkah Kedua,
Pemberian IP Addess pada setiap PC :

- Pemberian IP Address pada PC1

- Pemberian IP Address pada PC2

- Pemberian IP Address pada PC3

Langkah Ketiga, Konfigurasi EIGRP pada setiap router...

Sebelum melakukan konfigurasi EIGRP, Kita berikan IP Address pada setiap router ...

- Pemberian IP pada router0 :

Continue with configuration dialog? [yes/no]: no


Press RETURN to get started!


Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip address 192.186.11.1 255.255.255.0
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#int se2/0
Router(config-if)#ip address 174.16.14.1 255.255.0.0
Router(config-if)#band 125
Router(config-if)#cl ra 125000
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#exit

Router(config)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]
Router#

Konfigurasi EIGRP pada Router0 :


Router(config)#router eigrp 2
Router(config-router)#net 192.186.1.1
Router(config-router)#net 174.16.14.1
Router(config-router)#exit
Router(config)#exit

Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]
Router#

- Pemberian IP pada router1 :

 
Continue with configuration dialog? [yes/no]: no


Press RETURN to get started!


Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip address 200.186.1.1 255.255.255.0
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#int se2/0
Router(config-if)#ip address 174.16.14.2 255.255.0.0
Router(config-if)#band 125
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#exit

Router(config-if)#exit
Router(config)#int se3/0
Router(config-if)#ip address 14.14.1.1 255.0.0.0
Router(config-if)#band 125
Router(config-if)#cl ra 125000
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial3/0, changed state to down
Router(config-if)#exit 
Router(config)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]
Router#

Konfigurasi EIGRP pada Router1 :


Router(config)#router eigrp 2
Router(config-router)#net 200.186.1.1
Router(config-router)#net 174.16.14.2
Router(config-router)#net 14.14.1.1
Router(config-router)#exit
Router(config)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]
Router#

- Pemberian IP pada router2 :

     --- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no


Press RETURN to get started!



Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip address 210.186.1.1 255.255.255.0
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#int se2/0
Router(config-if)#ip address 14.14.1.2 255.0.0.0
Router(config-if)#band 125
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#exit
Router(config)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]
Router#


Konfigurasi EIGRP pada Router2 :


Router(config)#router eigrp 2
Router(config-router)#net 1210.186.1.1
Router(config-router)#net 14.14.1.2
Router(config-router)#end
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]
Router#

Setelah selesai semuanya, sekarang kita coba PING antara PC ke PC..
Apabila kurang jelas tutorial ini bisa di tanyakan...

Selamat mencobanya..